This is a full package (aircraft and panel) for FSX or FSX plus ServicePack1.

DO NOT INSTALL THIS FILE IF YOU DON'T FEEL SURE ABOUT NOTES 1 AND 2

(Please read Notes at the bottom of this page before installing).


FOREWORD
==========

The SIPA 300 was a tandem two-seat ab-initio jet trainer first flown in September 4, 1954. It was powered by a 350 lbst Turboméca Palas, as the Sipa 200. Provisions were made for the installation of a more powerful Turboméca Marboré II.

Thank you for downloading this package, we hope you'll enjoy it.

IMPORTANT!
===========
You MUST also insert the enclosed 'GougeSound.dll' in the Main FSX folder (if you don't have it yet) otherwise you will experience an FS crash!!!


FREEWARE!
=========

This model features reflective metallic skin and full animations.
The panel background is based on photographic material found in the net.
Included in this model there is also a Virtual Cockpit, with working essential flight instruments and animated flight controls, plus camera definition views.



INSTALLATION
============
Please DO NOT use installers.
Unzip this file into your Flight Simulator X\SimObjects\airplanes, folder and you will find the "SIPA_300" folder with the usual subfolders and a 'GougeSound.dll', then operate as follows:

Copy the enclosed 'GougeSound.dll' then Paste in your main Flight Simulator X folder (if you don't have it yet).

We think this should be the end of the installation procedure.

Enjoy.


TIPS
====
Please do not hesitate to use elevator trim as required to fly the plane hands-off.
The model is somewhat nose heavy at Take Off... please use nose up trim before or during Take Off run.
Flying on virtual cockpit you can move the eyepoint as required for better vision (check your eyepoint keyboard on FS options\controls\assignements for the keys required to move the 'eyepoint of view' (left/right/up/down/back or forward).
Please use ''A'' key to cycle views within a category and 'S' to change category (check the quick reference key commands).

DISCLAIMER
==========
THE MODEL HAS BEEN TESTED MANY TIMES TO ENSURE THE PROPER
OPERATION, AND ALL IS DONE TO AVOID ERRORS.

WE WILL NOT ACCEPT ANY RESPONSIBILITY FOR CONSEQUENTIAL INCIDENTAL
OR ANY SYSTEM DAMAGE DUE TO THE FAILURE OR IMPROPER OPERATION OF
THE SOFTWARE. THERE IS NOT ANY WARRANTY EXPRESSED OR IMPLIED FOR
ANY CIRCUMSTANCE.

NOT TO BE SOLD! THIS SOFTWARE IS FREEWARE !

Any comments and sugestions please write to:

Capt. I. D'Attomo
mdattom@tiscali.it

Capt. G.Quai
giovanni.quai@tin.it

The authors grant permission for repainting purposes only.

NOTE:
We installed succesfully this model on our FSX original and FSX Deluxe Edition plus SP1 without installers, simply following the above procedure.
Simmers running Sp2 and/or accelerators might encounter some not desired effects.

Note 1: Loading the aircraft for the first time in the FSX you will get an 'unknown author' message for each of our gauges.
Click 'YES' if you like our gauges or 'NO' if you don't. If you say 'NO' you will not have our instruments displayed on the panel, except the default ones.
Note 2: You will get a second message asking you to "trust" the related gauge; if you click "Yes" when asked, you will never be asked again.

PLEASE READ CAREFULLY BOTH MESSAGES .

Note 3: If you want to see a different panel, copy or aliase a panel of a single engine jet airplane of your choice: in this case, the VC will not be shown correctly.
You might also create a panel by removing our gauges and installing your preferred.

Note 4: Installing & using this package is at your own risk.

Note 5: FSX-Settings\Display\Graphics; selecting ''Light_Bloom'' check box, in the global options window, might not be compatible with our model and the selected plane may not appear.


April, 2010

P.S. more freeware aircrafts from the above authors may be found in 'SurClaro'. Just write one of the authors' name in the 'search for text' box.